Thermostatic Shower Kit Shower Set Bathroom Shower Set Shower System Bathroom Accessories G1/2 Thread Thermostatic Mixer Showering System With Top Spray Hand Shower For Home

Arrives by Wed, Feb 14 Buy Thermostatic Shower Kit Shower Set Bathroom Shower Set Shower System Bathroom Accessories G1/2 Thread Thermostatic Mixer Showering System With Top Spray Hand Shower For Home at
<b>thermostatic shower kit shower set bathroom shower set shower system bathroom accessories G1/2 Thread Thermostatic Mixer Showering System with Top Spray Hand Shower for Home</b><br/><b>Specification:</b><br/>Item Type: Thermostatic Shower Kit<br>Material: Brass<br>Color: Matte Black<br>Weight: Approx. 5200g / 183.4oz<br>Product Process: Electroplating<br>Opening Method: Knob type<br>Inlet and Outlet Pipe Diameter: G1/2 thread<br>Function Category: Hot and cold mixed water<br>Installation Type: Wall-mounted<br>Nominal Pressure: 12kg<br>Working Temperature: 1-50 degrees Celsius <br><br>Installation Steps:<br>1. Refer to the installation dimension drawing to pre-bury cold and hot water supply pipes in the wall, facing the wall, with hot water on the left and cold water on the right. Note: The cold and hot water supply pipes must be kept in the same horizontal position, and the center distance must be 150±10mm<br>2. Wrap the eccentric ① joint with PTFE tape and connect it to the cold and hot water supply pipes. Note: Do not use too much force at each connection to avoid damage to the thread<br>3. a Install the decorative wall cover ② on the off-center street, and screw it to the wall to be flat.<br>b Put the filter flat assembly ③ into the nut ⑨ and lock the eccentric joint ① to fix the body on the wall.<br>4. The body is installed.<br>5. a Refer to the installation dimension drawing on the left, draw the installation position of the fixing seat on the wall with a pencil, and punch holes with a percussion drill.<br>b Drive in the expansion rubber sleeve and fix the fixing seat on the wall with screws.<br>6. a Press the button on the shower sliding socket and put the shower sliding socket on the straight pipe assembly.<br>b Install the lifter, O- and elbow assembly on the straight pipe.<br>c Rotate the lifter to lock the two pipes.<br>Note: Do not use too much force at each connection to avoid damage to the thread<br>7. a Insert the fixed bottom of the lifter into the fixed seat, and connect the lower end of the shower column to the body through a nut.<br>b Adjust the shower column to be parallel to the wall, and tighten the screw to fix it.<br>8. Install the top spray on the elbow assembly.<br>9. Tighten one end of the shower hose to the hand shower, and the other end to the connector.<br>10. After installation, check whether there is any leakage at each connection.<br> <br/><br/><b>Package List:</b><br/><div>1 x Mixing Valve Body</div><div>1 x Handheld Shower Hose</div><div>1 x Hand Shower</div><div>1 x 10 inch Top Spray</div><div>1 x Shower Pipe Assembly with Lifting Base</div><div>1 x Fixed Base for Shower Pipe Fittings</div><div>2 x Decorative Cover</div><div>2 x Eccentric Connector</div><div>5 x Filter</div><div>1 x </div><div>1 x Expansion Screw</div><div>1 x Screw</div><div>1 x Hex Wrench</div><div>1 x Instruction Manual</div> <br/><br/><b>Note:</b><br/><div>1. Before replacing or disassembling the faucet, you must first cut off the water source, then turn on the faucet, release the water pressure, and check the waterway to make sure it is completely closed.</div><div>2. Before installing the faucet, be sure to clear the impurities and sludge in the pre-buried cold and hot water supply pipes to avoid clogging and affecting the water outlet function!</div><div>3. The working water pressure of the faucet is 0.5-5kgf/c㎡.</div><div>4. If the picture or text description in this installation manual does not match the

MR. TAP SHOWER MIXER MR. TAP SHOWER MIXER